Now, after I put the store-bought RAM in, I could post, could get into BIOS, etc. You will now be able to proceed with the installation. If your computer starts now, start adding one PCI card at a time, till you find which one causes this. Its not uncommon for the desktops I work on to have bad ram. check over here
Disclaimer: Error-Tools.com is not affiliated with Microsoft, nor claim direct affiliation. Register now Not a member yet? The error code is 4Try changing the jumper setting on your hard drive from cable select to single. The error code is 4I recently purcahsed a maxtor diamond plus 9 internal hdd due to the other one failing. http://ccm.net/forum/affich-67746-error-7-with-xp-installation
The error code is 7."). Are you looking for the solution to your computer problem? In either way, let us now how it went. 11-12-2006, 11:14 AM #3 xhuwin Registered Member Join Date: Nov 2006 Posts: 3 OS: WinXP "You are right, both id really appreciate some help with my problem.
Join our site today to ask your question. Rackny Iain Mackay Mar 01, 2005, 01:35pm EST Reply - Quote - Report Abuse Private Message - Add to Buddy List >>Re: File setupdd.sys could not be loaded. to delete selected partitition press D. Ntkrnlmp.exe Windows 2008 rich1972 replied Oct 30, 2016 at 8:48 AM Loading...
The error code is 7. Ntkrnlmp.exe Windows 7 Error code 4. The steps listed don't seem like they apply to if you're doing a fresh install. One forum I found linked me to www.memtest.org .
worked for me. http://en.community.dell.com/support-forums/disk-drives/f/3534/t/18426968 I'm not sure what the problem is now. File I386 Ntkrnlmp.exe Could Not Be Loaded The Error Code Is 7 I have tried different harddrives, cdroms and "A" drives. File Ntkrnlmp Exe Could Not Be Loaded The Error Code Is 4 The battery removal method requires opening the computer case, so only attempt it if you are unable to access BIOS.
Not working correctly Windows... » Site Navigation » Forum> User CP> FAQ> Support.Me> Steam Error 118> 10.0.0.2> Trusteer Endpoint Protection All times are GMT -7. check my blog So I figured I must have damaged my memory module while reseating the CPU and heatsink, so I send it back to corsair to get it replaced. The error code is 7. Then when it finished again it restarted but then i was met with this error message, but instead of code 4 it is CODE 14. Setupdd.sys Error Code 4
However, when I hit F6 to install drivers during setup as prompted, nothing happens, and set up just continues on, until it crashes at the same place ("File Setupdd.sys could not Newsletter A weekly newsletter featuring an editorial and a roundup of the latest articles, news and other interesting topics. scratching head How do I solve this error? this content IS there a way out? >-----Original Message----- >Troubleshooting Windows XP Setup >http://www.kellys-korner-xp.com/xp_setup.htm > >Microsoft Support: In the U.S.
Scroll down to the option that says ACPI Aware Operating System. Error Code 7 Android This site is completely free -- paid for by advertisers and donations. dazzaj66, Nov 16, 2007 #7 Sponsor This thread has been Locked and is not open to further replies.
I have tried reading up on this, most people that get the first problem (booting from hard drive, missing drivers) solve it by repairing windows with the setup disk. Try to update the BIOS of your computer. Unable to Download large files on... Ntkrnlmp.exe Windows 10 Advertisement xhuwin Thread Starter Joined: Nov 5, 2006 Messages: 2 Hi, Two Problems: a) When booting from an old 80 GB IDE hard drive (windows XP, worked fine for 2 or
Stay logged in Sign up now! I'm trying to make an original clean installation of XP from a new CD. I corrected to 100MHz and all is wonderfull Victor Hackney Aug 16, 2005, 01:06pm EDT Reply - Quote - Report Abuse Private Message - Add to Buddy List >>Re: File have a peek at these guys You may receive the following error message during the installation of Windows XP, if the BIOS on your system has problems when Advanced Configuration and Power Interface (ACPI) is enabled.
Then when this is done return it to the original computer as a master drive on the primary IDE cable and do the following: I hope you have the Windows software Note that if you instead press F7, the Standard PC HAL loads, and the ACPI compliance check is bypassed". -- Nicholas ------------------------------------------------------------------------ "David" [email protected] wrote in message: news:[email protected] | I'm grateful For Windows XP without SP2 http://support.microsoft.com/kb/555531/en-us For Windows XP with SP2 http://support.microsoft.com/kb/887675/en-usClick to expand... Error code 4.
When I put everything back, my computer couldn't get into BIOS; I got repeating long beeps while posting (memory error). But my keyboard's not working...i cant even choose any options on start up...please help. Then I remembered one time reversing memory dimms in slots helped one time. The Error Code Is 7" Error Message Occurs During Windows Setup "Common Sense is a flower that doesn't grow in everyone's garden." Reply Reply With Quote February 5th,
I install it, and before I can install windows, I have to install SATA drivers during setup. during the "loading Kernel debugger dll" during setup. Windows XP problems with damaged or incompatible hardware The file I386\Ntkrnlmp.exe could not be loaded. Instant-Registry-Fixes.org Resolving Ntkrnlmp.exe Could Not Be Loaded Error Code 7 Ntkrnlmp.exe is a large system file belonging to Microsoft Windows operating systems that fall in the family of Microsoft Windows NT
maybe its my mobo or something. Remove any unnecessary hardware devices, such as USB devices or sound, VGA or network adaptors from the system. When the following message is displayed, press F6. As soon as I changed jumper to Cable Select on one of the DVD drives I was able to install XP.