If I smack the pipe where the gas comes into the Tm-1, (only while it is sparking the gap of course), sometimes the burner will light. Check the wire connections. 711 (LED flashes one time) - Gas solenoid valve circuit failure. Download Troubleshooting Guides here. And this way, I would be checking voltage at the source, so if the high limit fuses were blown, this wouldn't affect my reading, since they are downstream, in series with Source
At least the cold showers match our current heat wave. -MClick to expand... Please try the request again. If the unit is performing in accordance with the flow chart, it may be undersized for the application. Page 1 of 2 1 2 Next > halogen25 New Member Joined: Jan 6, 2006 Hi All, I have had my Takagi T-K2 for 3 years and love it. http://www.takagi.com/professionals/troubleshooting-and-repair
More » Home Forums Forums Quick Links Search Forums Recent Posts Resources Resources Quick Links Search Resources Most Active Authors Latest Reviews Members Members Quick Links Notable Members Registered Members Current Overall, I like the way my HW system works (when it works!) but after only 4.5 years of service, I'm considering switching back to a gas tank heater. The system returned: (22) Invalid argument The remote host or network may be down.
External Troubleshooting A very high percentage of service problems requiring troubleshooting can usually be traced to causes external to the unit. Just a few turns of wire, around a plastic barrel the diameter of a finger. Same problem but when it did light and I gave the unit a high demand it would blow itself out. Takagi Tm1 Parts your acceptance and payment is entirely optionalNext step is to for you or I to call Takagi at the number below and ask for the complete trouble shooting manual showing voltage
The Tankless Advantage Safety Durability Water Valves Water Flow Water Heater Incentives Professionals Troubleshooting & Repair Installation Requirements Replacement Parts Application Diagrams Commercial Rack Systems Easy-Link System Multi-Unit System Sizing Guide Takagi Technical Support The upper temperature was set for 110F, and the outgoing water temp gradually increased from 110 to 135 over the course of about 5 minutes, with the burner finally shutting off If we find a solution, I'll be sure to post it here. http://www.hot-water-heaters-reviews.com/takagi-error-codes.html atpl53, Jan 30, 2012 #19 Scott Drew New Member Joined: Jan 20, 2015 Location: California Just wanted to say that my T-K3 was having the exact same issues, and all the
Gas Supply Line Problems: Undersized Line: There is a great tendency to just “hook up to the existing gas line,” which is usually only ½ inch diameter. Tankless Water Heater Error Codes The upper temperature was set for 110F, and the outgoing water temp gradually increased from 110 to 135 over the course of about 5 minutes, with the burner finally shutting off I was really expecting the coil to be "fried", but it seems ok so far.So I'm gonna remove the gas solenoid assembly, and see if it's corroded inside. On ours the upper or longer wire checked to have none confirmed by making jumper wire to by-pass and unit works perfect.
So what options are left for me? http://www.justanswer.com/hvac/7l2iq-hi-i-ve-takagi-mobius-tm-1-i-ve-111-fault.html How to use diagnostic system to repair the faulty Takagi heater. Takagi Tm1 Error Code 111 There is the possibility that the gas valve at the meter does not open up fully when first switched on, leading to insufficient pressure at the unit. Takagi Water Heater Troubleshooting If it ain't broke don't fix it.
Generated Sun, 30 Oct 2016 11:00:27 GMT by s_hp90 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.9/ Connection this contact form Also could be a faulty water flow sensor. I think the three little piggies are used to regulate the burner, for consistent water temperature. My general approach is to keep pushing for a more advanced person in the engineering or trouble shooting group until I get someone who can get me what I want.Toll Free Takagi Error Code 111
Environmental Issues: The heaters should be installed in relatively clean areas with access to sufficient combustion air that is free from dust, lint, grease, or chemicals. All rights reserved. If it was a Noritz unit they would send out a service technician to trouble shoot it for you, and make the needed repairs. have a peek here It still can happen just not very likely.
It would spark and light off but after a few seconds it would it would shut-down amd recycle. Takagi T-m1 Specs Also, you might have to clean out the burner. Hello again, be aware that these gas valves are safety items as well as control items and are not generally intended to be repaired in the field...
So I replaced the flame sensor and ignightor since I noticed the gasket was torn and missing 1/2 inch of material. The unit is no longer under warranty (with the exception of the heat exchanger), and all the usual suspects have been ruled out. Call first however.. Takagi Error Code 121 According to the Takagi electrical schematic, somewhere near this connector are two "high limit" fuses, but I can't see them anywhere.
Make sure that you order the correct heater for the type of gas you will be using, Natural Gas or Liquid Propane. The TM-1 starts up normally, starts sparking the igniter, and my meter reads various voltages across the MV coil. (I had it on AC). Here is what I know. Check This Out then point out that their published manual on the web is not providing anything close to viably trouble shooting their system.It will be better if you call them, on Monday.That person
First thing they will check is there is no obstruction in the flue pipe.