Measure the AC line voltage between pins CN1-1 and CN1-3 on the board. Amazon, the Amazon logo, Endless, and the Endless logo are trademarks of Amazon.com, Inc. Error 53 Unformatted or Defective Flash - Flash problem at POR or while attempting to write. Error 928 Erase lamp assembly missing or disconnected Error 929 The toner sensor is not operating properly, the developer drive assembly is not operating properly or the print cartridge is Source
Intterconnect Board Error 940-943 Color Machines Toner Metering Cycle failure CMKY cartridge 940 = Cyan cartridge 941 = Magenta cartridge 942 = Yellow cartridge 943 = Black cartridge Toner metering cycle Thank you and your firm again, you were terrific. Additional info on X and XX codes available by email. Jump to error 92X Some Lexmark printers have indicator lights which indicate by solid, blinking or off, an error condition.
Error 923 Fuser is too hot while printing or when idle. • Short in the thermistor circuit. • Noisy thermistor signal • Fuser is actually overheating due to hardware faults. Regularly replacing crucial parts prevents bothersome breakdowns. I am new to this and do not want to screw this up.
If the AC line voltage at CN1 is incorrect, check fuse F2. I will have purchasing call in an order. Check connecting cables for continuity. Lexmark Error Codes Problem The heated roller is heated by a halogen lamp or in some cases a solid state ceramic heating element and is subject to failure.
Check the operation of the toner sensor. Lexmark Printer Error Messages Error 26 Duplex unit is installed but paper tray is not sensed. Error 30 30 Top Cover Open or Print Cartridge Missing Make sure the spring-mounted pin on the printhead shroud is installed properly and that it is detected by the ramp on Perhaps you were trying to rebuild a unit or someone was rebuilding a unit and put the wrong lamp in and failed to test it before it was shipped out.
It can also be the LVPS (low voltage power supply) or a fuse in the power supply on some models. Service Error 146.00 Dc Pick Motor Any help here would be appreciated too. Controller Board 2. We got it this morning and I have it installed.
Load correct size Error 28 Input sensor not made after pick attempt. http://support.lexmark.com/index?pmv=print&page=content&locale=en&productCode=OPTRA_S_1625&segment=SUPPORT&userlocale=EN_US&id=SO1539 If the lamp turns on then check the thermistor and clean if needed.Below are the voltage checks. Lexmark Error Codes The machine thinks that the wrong lamp is installed. Lots of these Lexmark fusers look the same and can accidentally be installed in the wrong machine if you have them laying Lexmark Engine Error Thunderstorms, electrical work nearby, or windy days can cause sudden short power interruptions.
Resistance: â€¢ HOT J2-1 - J2-2 = 2.5K ohms â€¢ COLD 150K ohms to 260K ohms7. this contact form Notify me of new posts by email. Remove and reinstall print cartridge. Also, you will find links to purchase a replacement fuser and at the bottom of this page find a link to the illustrated instructions on removing the fusing unit.Lexmark 99A2423 110-127V Lexmark Printer Error Code Ec5
If you get the error and the lamp doesn't turn on then check continuity across the lamp, lamp contact points, wiring, and thermal fuse.4. Replace Printhead Pricing Error 936 Error 937 Error 936/937 Main Drive Motor, Transport Motor An error with the main drive motor has been sensed by the printer Optra s 2450 Optra Any print quality problems such as lines that arespaced 51.02 mm apart indicate you should check the transfer rollfor damage, toner or foreign material buildup.Service Tip: The transfer roll assembly is have a peek here Ask the customer if they have replaced the transfer roll recently.CAUTION: Make sure the printer is powered off before making anychecks on the transfer roll or associated parts for personal safety
If the machine starts working again then keep an eye on it. 938.06 Service System Electronics Customers also search for: Fuser; Fuser Kit; LexmarkTM T520, T522. Measure the AC line voltage between the two connectors on the fuser end of the LVPS to fuser AC cable.
San Rafael, CA Great that you have that part in stock and thank you for your quick reply. Remove the redrive assembly, turn the machine back on, tell it to print a test page, watch to see if the lamp turns on in the fusing assembly.3. A 920 error caused by low line voltage can sometimes be cleared by turning the machine off and then on again. Lexmark Printer Error Lights Be sure the correct type of fuser lamp is installed in the printer.Service Manual Service Tips for the Lexmark T522, T520 Error Code 925 If the correct lamp is installed and
Can also be LVPS or system board. Replace Printhead Pricing Error 931 Printhead error - No first sync - check connections at both ends of cable for corrosion or oxidation. Newer machines display a sub code to indicate which condition applies. Check This Out Overall Product Weight: -6 Pounds.
At least that's my own personal experience. If the printer is expecting a toner addition cycle but one is not detected, a 94x TMC Error is displayed. Verify latch relay is operating - slowly close door and listen for interlock switch 3. Replace System Board Request Quote Error 917 Check the transfer roller for toner buildup, surface damage to the roller, oil, or other contaminants on the surface of the roller.
LVPS to Fuser AC Cable Caution: When taking measurements for AC power, observe all safety precautions. To verify that the printer recognizes all the installed memory, go to the user menus and print the Print Menus test page. Houve um erro com o aplicativo. Anyway.
If cables, connectors and connections are good replace assemblies listed. Lots of times this can fix your problem. Check printhead, cable, motor, system board. Open the printer rear door to access the jam.
Replace the fusing assembly.Click on the link below for the fuser replacement instructions -- Lexmark T522, T520 Fuser Replacement Procedure --Lexmark 99A2423 110-127V Fuser (LEX99A2423) Category: FusersSee larger imageItem #: LEX99A2423. The pin should enter the tower on the HVPS and depress the cover switch. Works great and certainly solved the problem (as I expected it would). -Alan A. Tray is empty or not installed, paper jam in entry throat, or printer is requesting a manual feed.
It may take the printer 10-20 seconds to determine if the print cartridge is defective. The main motor assembly may need to be replaced.